基于密闭爆发器试验的发射装药内弹道性能预估

为了预估发射装药的内弹道性能,建立了一种基于密闭爆发器试验检测发射药的静态燃烧性能参数进而预测其装药内弹道性能的方法,采用不同批次的单樟-5/7发射药进行了装药性能预估计算,并基于30 mm火炮对内弹道性能预估精度进行了试验验证。结果表明,采用所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法计算获得的最大膛压为376.0 MPa,与试验测试的膛压平均值388.7 MPa的计算误差为3.27%;计算的炮口初速为1143.5 m/s,与试验测试的炮口初速平均值1156.3 m/s的计算误差为1.11%。所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法具有较高的精度,可对发射药样品不同批次间的内弹道性能进行高效精确的预估,为长期贮存发射药使用寿命的判定及发射药产品的出厂校验提供了一种高效低成本的弹道性能评价方法。     

Fabrication of novel silicon carbide-based nanomaterials with unique hydrophobicity and microwave absorption property

Novel SiC-based nanomaterials, namely the nitrogen and aluminum co-doped SiC@SiO₂ core-shell nanowires and nitrogen-doped SiO₂/Al₂O₃ nanoparticles, have been fabricated through a facile thermal treatment process based on the chemical vapor deposition and vapor-liquid reaction. These nanomaterials show remarkable hydrophobicity with a water contact angle (CA) over 140°, which are aroused by the surface zigzag morphology of the nanostructures and the hydrocarbyl groups generated during the preparation process. Moreover the nanocomposites also exhibit relatively prominent microwave absorption (MA) properties in the frequency range of 2.0-18.0 GHz. The minimum reflection loss (RL) value as low as −23.68 dB can be observed at 14.16 GHz when the absorber thickness is 2.6 mm with a loading rate of 16.7 wt%. And the nanocomposites-based absorbent can achieve an effective absorption bandwidth (RL < −10 dB) of 4.48 GHz with the absorbent thickness of 2.5 mm. This enhanced microwave attenuation performance can be attributed to multiple polarizations and perfect impedance matching conditions, as well as multiple internal reflections. These marvelous properties make these N and Al co-doped SiC@SiO₂ core-shell nanowires and N-doped SiO₂/Al₂O₃ nanoparticles display extensive application potential as MA materials in harsh environment.     

淬火配分处理对锻态Fe-0.2C-9Mn-3.5Al钢显微组织及力学行为的影响

分析了淬火配分处理对锻态Fe-0.2C-9Mn-3.5Al钢显微组织及力学行为的影响。结果表明,热处理态试验钢主要由块状δ-铁素体、马氏体和板条状残留奥氏体等多相构成;残留奥氏体的体积分数随等温淬火温度升高而增大,在310 ℃时达到峰值;310 ℃等温淬火后在400 ℃配分3 min时可以获得较优的综合力学性能,抗拉强度和断后伸长率分别为1175 MPa和21.50%,强塑积达到25.26 GPa·%;应力-应变曲线中存在着明显的“锯齿”状起伏,可能与亚稳态的残留奥氏体集中转变为马氏体有关。     

Effects of Ga and Sn on the electrochemical behavior of Mg–6Al–1Zn as anode materials

The microstructure and electrochemical behavior of Mg–6Al–1Zn, Mg–6Al–1Zn–1Ga, Mg–6Al–1Zn–1Sn, and Mg–6Al–1Zn–0.5Sn–0.5Ga as anode materials in a 3.5 wt% NaCl solution are compared systematically. The results show that Sn alloying refines the second-phases of Mg–6Zn–1Al by promoting tiny granular Mg₁₇Al₁₂ phases containing Sn, and inspires their disperse distribution. However, the Ga results in the formation of semicontinuous reticular Ga containing Mg₁₇Al₁₂ phases. The comparison of discharge tests indicates that Mg–6Al–1Zn–1Sn has the highest discharge activity, and Mg–6Al–1Zn–1Ga displays the largest hydrogen evolution corrosion resistance in 3.5 wt% NaCl solution at 298 K. The synergy of Ga and Sn can shorten discharge activation time and promote low discharge potential. In addition, the utilization efficiencies of the alloys decrease as follows: Mg–6Al–1Zn–1Ga > Mg–6Al–1Zn–0.5Sn–0.5Ga > Mg–6Al–1Zn–1Sn > Mg–6Zn–1Al. This study illustrates that the Mg–6Al–1Zn–0.5Sn–0.5Ga alloy has acceptable utilization efficiency and desirable electrochemical activity, which implies that doping Ga and Sn obtains a balance between discharge activity and utilization efficiencies.     

Al3Zr/Al基原位复合材料等离子体焊接区的组织及表面腐蚀行为

摘要： 本文以5wt%Al3Zr/铝基复合材料为研究对象，以Ar气体为离子气体，Al-Ti-B为丝材进行等离子焊接。用电化学综合测试仪测定了焊接区在3.5%NaCl溶液中的腐蚀极化曲线。采用扫描电子显微镜（SEM）、X射线衍射仪（XRD）对复合材料及其焊缝的组织和相组成进行了分析和表征，研究了Al3Zr/Al基复合材料等离子焊接后在3.5%NaCl溶液中的腐蚀行为和腐蚀机理。SEM分析结果表明，等离子弧焊接可获得较好的焊缝组织，焊缝组织主要由Al3Ti相和Al基体组成，Al3Ti相呈条状和球形。电化学极化曲线表明，材料在熔核处的耐蚀性略低于母材，焊缝处浸泡腐蚀机理为Al3Ti相和基体相的电极电位不同形成原电池反应造成。     

Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

Synergistic effect of glass fibre and Al powder on the mechanical properties of glass-ceramics

To explore the synergistic effect of glass fibre and Al powder on the mechanical properties of glass-ceramics, blast furnace slag was chosen as the main material, and glass fibre and Al powder as reinforcement materials. The phase compositions, microstructures, compressive properties, and apparent density of the glass-ceramics with varying quantities of glass fibre and Al powder were investigated. The experimental results indicated that Al powder could exist as a simple substance in glass-ceramics and form a dense net coating on the surface of blast furnace slag to improve the plasticity of the glass-ceramic. The glass fibre had better reinforcement effect than Al powder because of its extremely high mechanical strength. The plasticity of glass-ceramics, however, severely decreased; the glass-ceramics exhibited brittle failure during compression. A slight increase in the content of CaSi₂ and SiO₂ in the glass-ceramics was closely related to the addition of glass fibre. Considering safety and economy, glass-ceramics with 6% Al and 14% glass fibre (S4) have the best mechanical properties. The compressive strength, strain at maximum force, and apparent density were 40?MPa, 19% and 1.974?g/cm³, respectively.     

金属有机框架材料MIL-53(Al)-F127对双酚A的吸附性能

采用一步溶剂热法制备具有介孔结构金属有机框架材料MIL-53(Al)-F127，用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射仪(XRD)、傅里叶红外变换光谱仪(FTIR)、全自动比表面积及孔隙度分析仪(BET)等手段表征其形貌和结构，探究其对双酚A(BPA)的吸附性能并与微孔结构的MIL-53(Al)对比，研究了吸附剂的含量、pH以及温度对其吸附性能的影响。结果表明，介孔结构金属有机框架材料MIL-53(Al)-F127对双酚A具有良好的吸附性能；在pH值为6、温度为30℃条件下MIL-53(Al)-F127在20 min左右达到最大平衡吸附量为27.2 mg/g，去除率达到92%。其吸附动力学模型拟合结果，符合准二级动力学曲线。